耐壓試驗又稱強度試驗，屬于安全性能指標試驗。試驗壓力為公稱壓力的1.5倍，試驗用加壓介質為純凈的水，其氯離子含量不應超過25ppm。每一支產品都要進行耐壓試驗。采用手動的或電動的試壓泵加壓，壓力觀測通常可用1.5--4倍試驗壓力量程的1.5級以上壓力表，或等同功效的壓力測試儀器。試驗時，將軟管試件平直放置，一端安裝帶有排氣閥的堵頭，另一端和試壓泵出口管相連接，將水注入管內，排盡空氣，關閉排氣閥，然后緩慢增加壓力至規定的試驗壓力值，保壓5mm后，檢查試樣狀況，有無滲漏、零件損壞等異常的失效形式出現。合格品要求不允許有滲漏跡象或零件損壞等異常的失效形式出現。

　　檢驗項目及檢驗方法金屬波紋管的性能檢測指標主要有七項:外觀、尺寸、耐壓、氣密性、靜態彎曲、動態彎曲、爆破。其中外觀、尺寸、耐壓和氣密性屬于出廠檢驗項目，型式試驗時要求七個項目全部進行檢驗。本文主要對耐壓、氣密性、靜態彎曲、動態彎曲和爆破等五個項目進行論述。